自潤凸緣襯套80F
產品系列
點擊圖片放大商品名稱:
自潤凸緣襯套80F
自潤凸緣襯套80F
詳細介紹:
自潤凸緣襯套80F
請選擇適合的內徑、厚度之Parts No.
（例如）內徑15mm、厚度10mm時，請以80F-1510標示。
內徑 | 外徑 | 凸緣外徑 | 長度 L 公差 0 -0.3 | |||||||||||
Ød | 公差 | ØD | 公差 | ØF | t | 公差 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 10 |
2 | +0.065 +0.015 | 4 | +0.107 +0.032 | 6 | 1 | 0 -0.10 | 0202 | 0203 | 0204 |
|
|
|
|
|
3 | +0.080 +0.030 | 5 | " | 8 | " | " |
| 0303 | 0304 | 0305 | 0306 |
|
|
|
4 | +0.095 +0.045 | 6 | " | 9 | " | " |
| 0403 | 0404 | 0405 | 0406 |
|
|
|
5 | " | 7 | +0.157 +0.045 | 10 | " | " |
| 0503 | 0504 | 0505 | 0506 | 0507 |
|
|
6 | " | 8 | " | 12 | " | " |
| 0603 |
| 0605 | 0606 |
| 0608 | 0610 |
7 | " | 9 | " | 13 | " | " |
| 0703 |
| 0705 |
| 0707 |
| 0710 |
8 | +0.120 +0.060 | 10 | " | 15 | " | " |
| 0803 |
| 0805 | 0806 |
| 0808 | 0810 |
9 | " | 11 | +0.193 +0.058 | 16 | " | " |
| 0903 |
| 0905 | 0906 |
|
| 0910 |
10 | " | 12 | " | 18 | " | " |
| 1003 |
| 1005 | 1006 |
| 1008 | 1010 |
12 | " | 14 | " | 20 | " | " |
|
|
|
| 1206 |
| 1208 | 1210 |
14 | " | 16 | " | 22 | " | " |
|
|
|
|
|
|
| 1410 |
15 | " | 17 | " | 23 | " | " |
|
|
|
|
|
|
| 1510 |
16 | " | 18 | " | 24 | " | " |
|
|
|
|
|
|
| 1610 |
18 | " | 20 | +0.221 +0.071 | 26 | " | " |
|
|
|
|
|
|
| 1810 |
20 | +0.145 +0.075 | 23 | " | 31 | 1.5 | 0 -0.15 |
|
|
|
|
|
|
| 2010 |
22 | " | 25 | +0.231 +0.081 | 33 | " | " |
|
|
|
|
|
|
| 2210 |
25 | +0.170 +0.090 | 28 | " | 36 | " | " |
|
|
|
|
|
|
| 2510 |
30 | " | 34 | +0.290 +0.095 | 42 | 2 | " |
|
|
|
|
|
|
| 3010 |
32 | +0.215 +0.115 | 36 | " | 46 | " | " |
|
|
|
|
|
|
|
|
35 | " | 39 | " | 49 | " | " |
|
|
|
|
|
|
| 3510 |
38 | " | 42 | +0.340 +0.115 | 52 | " | " |
|
|
|
|
|
|
|
|
40 | " | 44 | " | 54 | " | " |
|
|
|
|
|
|
|
|
45 | +0.235 +0.135 | 50 | +0.430 +0.130 | 60 | 2.5 | " |
|
|
|
|
|
|
|
|
50 | " | 55 | " | 65 | " | " |
|
|
|
|
|
|
|
|
- ●＃80F自潤凸緣襯套為射出成形品。
- ●內徑公差是襯套壓入ØD±0.002的環規所測數值。
- ●在0℃以下使用時，會因熱收縮而使襯套脫落，所以必須要設防止脫落。
長度 L 公差 0 -0.5 | 倒角尺寸 | 內徑 | ||||||||
12 | 15 | 20 | 25 | 30 | 40 | 50 | a | b | c | Ød |
|
|
|
|
|
|
| 0.3 | 0.3 | C0.3 | 2 |
|
|
|
|
|
|
| 〞 | 1 | 〞 | 3 |
|
|
|
|
|
|
| 〞 | 〞 | 〞 | 4 |
|
|
|
|
|
|
| 〞 | 〞 | 〞 | 5 |
|
|
|
|
|
|
| 〞 | 〞 | 〞 | 6 |
|
|
|
|
|
|
| 〞 | 〞 | 〞 | 7 |
0812 | 0815 |
|
|
|
|
| 〞 | 〞 | 〞 | 8 |
0912 | 0915 |
|
|
|
|
| 〞 | 〞 | 〞 | 9 |
1012 | 1015 | 1020 |
|
|
|
| 〞 | 〞 | 〞 | 10 |
1212 | 1215 | 1220 |
|
|
|
| 〞 | 〞 | 〞 | 12 |
1412 | 1415 | 1420 |
|
|
|
| 〞 | 〞 | R0.4 | 14 |
1512 | 1515 | 1520 | 1525 | 1530 |
|
| 〞 | 〞 | 〞 | 15 |
1612 | 1615 | 1620 | 1625 | 1630 |
|
| 〞 | 〞 | 〞 | 16 |
1812 | 1815 | 1820 | 1825 | 1830 |
|
| 〞 | 〞 | 〞 | 18 |
2012 | 2015 | 2020 | 2025 | 2030 |
|
| 〞 | 〞 | 〞 | 20 |
| 2215 | 2220 | 2225 | 2230 |
|
| 〞 | 〞 | 〞 | 22 |
2512 | 2515 | 2520 | 2525 | 2530 |
|
| 〞 | 〞 | 〞 | 25 |
3012 |
| 3020 | 3025 | 3030 | 3040 |
| 〞 | 〞 | 〞 | 30 |
|
| 3220 | 3225 | 3230 | 3240 |
| 〞 | 〞 | 〞 | 32 |
3512 |
| 3520 | 3525 | 3530 | 3540 |
| 〞 | 〞 | 〞 | 35 |
|
| 3820 |
| 3830 | 3840 |
| 0.5 | 2 | R0.6 | 38 |
4012 |
| 4020 | 4025 | 4030 | 4040 | 4050 | 〞 | 〞 | 〞 | 40 |
|
| 4520 | 4525 | 4530 | 4540 | 4550 | 〞 | 〞 | R0.8 | 45 |
|
| 5020 |
| 5030 | 5040 | 5050 | 〞 | 〞 | 〞 | 50 |
更多商品
自潤耐磨板CWP #2000 -廣汎應用型
自潤耐磨板-廣汎應用型 CWP #2000 請選擇適合的寬度、長度之Parts No. （例如）寬度58mm、長度150mm時，請以CWP-58150標示。 ☆：W＝38.48製品的倒角尺寸。 ★：W＝125的製品是37.5。 ：W＝38的製品倒角尺寸。 Parts No. 寬度 長度 厚度 裝配孔之孔距 裝配 孔數 倒角 形狀 W 公差 L 公差 T 公差 l 1 公差 l 2 CWP-3875 38 -0.1 -0.3 75 -0.1 -0.3 20 ±0.01 45 ±0.2 15 2 B CWP-38100 " " 100 " 20 " 50 " 25 2 B CWP-38150 " " 150 " 20 " 100 " 25 2 B CWP-4875 48 " 75 " 20 " 45 " 15 2 B CWP-48100 " " 100 " 20 " 50 " 25 2 B CWP-48125 " " 125 " 20 " 75 " 25 2 B CWP-48150 " " 150 " 20 " 100 " 25 2 B CWP-48200 " " 200 " 20 " 100 " 50 2 B CWP-48250 " " 250 " 20 " 100 " 25 3 D Parts No. 寬度 長度 厚度 裝配孔之孔距 裝配 孔數 形狀 W 公差 L 公差 T 公差 W1 公差 W2 l 1 公差 l 2 CWP-7575B 75 -0.1 -0.3 75 -0.1 -0.3 20 ±0.01 － － － 25 ±0.2 25 2 B CWP-75100B " " 100 " " " " " " 50 " " " B CWP-75125 " " 125 " " " " " " 75 " " " B CWP-75150 " " 150 " " " " " " 100 " " " B CWP-75200 " " 200 " " " " " " 150 " " " B CWP-75250 " " 250 " " " " " " 100 " " 3 D CWP-75300 " " 300 " " " " " " " " 50 " D CWP-100100 100 " 100 " " " 50 ±0.2 25 50 " 25 4 C CWP-100125 " " 125 " " " " " " 75 " " " C CWP-100150 " " 150 " " " " " " 100 " " " C CWP-100200 " " 200 " " " " " " 150 " " " C CWP-100250 " " 250 " " " " " " 200 " " " C CWP-100300 " " 300 " " " " " " " " 50 " C CWP-125125 125 " 125 " " " " " 37.5 75 " 25 " C CWP-125150 " " 150 " " " " " " 100 " " " C CWP-125200 " " 200 " " " " " " 150 " " " C CWP-125250 " " 250 " " " " " " 200 " " " C CWP-125300 " " 300 " " " " " " " " 50 " C CWP-150150 150 " 150 " " " 100 " 25 100 " 25 " C CWP-150200 " " 200 " " " " " " 150 " " " C CWP-150250 " " 250 " " " " " " 200 " " " C
自潤耐磨板CWX #2000(厚板10mm型)
自潤耐磨板(厚板10mm型)CWX #2000 請選擇適合的寬度、長度之Parts No. （例如）寬度75mm、長度125mm時，請以CWX-75125標示。 . Parts No. 寬度 長度 厚度 裝配孔之孔距 裝配 孔數 形狀 W 公差 L 公差 T 公差 l 1 公差 l 2 CWX-2875 28 -0.1 -0.3 75 -0.1 -0.3 10 ±0.01 45 ±0.2 15 2 A CWX-28100 " " 100 " " " 50 " 25 " A CWX-28125 " " 125 " " " 75 " " " A CWX-28150 " " 150 " " " 100 " " " A CWX-3875 38 " 75 " " " 45 " 15 " A CWX-38100 " " 100 " " " 50 " 25 " A CWX-38125 " " 125 " " " 75 " " " A CWX-38150 " " 150 " " " 100 " " " A CWX-4875 48 " 75 " " " 45 " 15 " A CWX-48100 " " 100 " " " 50 " 25 " A CWX-48125 " " 125 " " " 75 " " " A CWX-48150 " " 150 " " " 100 " " " A CWX-48200 " " 200 " " " " " 50 " A CWX-48250 " " 250 " " " " " 25 3 C CWX-7575 75 " 75 " " " 25 " " 2 A CWX-75100 " " 100 " " " 50 " " " " CWX-75125 " " 125 " " " 75 " " " " Parts No. 寬度 長度 厚度 裝配孔之孔距 裝配 孔數 形狀 W 公差 L 公差 T 公差 W1 公差 W2 l 1 公差 l 2 CWX-75150 75 -0.1 -0.3 150 -0.1 -0.3 10 ±0.01 － － － 100 ±0.2 25 2 A CWX-75200 " "" 200 " " " " " " 150 " " " A CWX-75250 " " 250 " " " " " " 100 " " 3 C CWX-75300 " " 300 " " " " " " " " 50 " C CWX-100100 100 " 100 " " " 50 ±0.2 25 50 " 25 4 B CWX-100125 " " 125 " " " " " " 75 " " " B CWX-100150 " " 150 " " "" " " " 100 " " " B CWX-100200 " " 200 " " " " " " 150 " " " B CWX-100250 " " 250 " " " " " " 200 " " " B CWX-100300 " " 300 " " " " " " " " 50 " B CWX-125125 125 " 125 " " " 75 " " 75 " 25 " B CWX-125150 " " 150 " " " 50 " 37.5 100 " " " B CWX-125200 " " 200 " " " " " " 150 " " " B CWX-125250 " " 250 " " " " " " 200 " " " B CWX-125300 " " 300 " " " " " " " " 50 " B CWX-150150 150 " 150 " " " 100 " 25 100 " 25 " B CWX-150200 " " 200 " " " " " " 150 " 25 " B CWX-150250 " " 250 " " " " " " 200 " " " B
自潤耐磨板FWP #500F-廣汎應用型
自潤耐磨板-廣汎應用型FWP #500F 請選擇適合的寬度、長度之Parts No. （例如）寬度58mm、長度100mm時，請以FWP-58100標示。 ☆：W＝28 • 38 • 48製品的倒角尺寸。 * ：※的製品尺寸為15。 ★：W＝125的製品是37.5。 ●：W＝28.38的製品倒角尺寸。 Parts No. 寬度 長度 厚度 裝配孔之孔距 裝配 孔數 形狀 W 公差 L 公差 T 公差 l 1 公差 l 2 FWP-2875 28 -0.1 -0.3 75 -0.1 -0.3 20 ±0.01 45 ±0.2 15 2 B FWP-28100 " " 100 " " " 50 " 25 " B FWP-28150 " " 150 " " " 100 " " " B FWP-3875 38 " 75 " " " 45 " 15 " B FWP-38100 " " 100 " " " 50 " 25 " B FWP-38150 " " 150 " " " 100 " " " B FWP-4875 48 " 75 " " " 45 " 15 " B FWP-48100 " " 100 " " " 50 " 25 " B FWP-48125 " " 125 " " " 75 " " " B FWP-48150 " " 150 " " " 100 " " " B FWP-48200 " " 200 " " " " " 50 " B FWP-48250 " " 250 " " " 100 " " 3 D FWP-5875 58 " 75 " " " 45 " 15 2 B FWP-58100 " " 100 " " " 50 " 25 " B FWP-58150 " " 150 " " " 100 " " " B Parts No. 寬度 長度 厚度 裝配孔之孔距 裝配 孔數 形狀 W 公差 L 公差 T 公差 W1 公差 W2 l 1 公差 l 2 FWP-7575B 75 -0.1 -0.3 75 -0.1 -0.3 20 ±0.1 － － － 25 ±0.2 25 2 B FWP-75100B " " 100 " " " " " " 50 " " " B FWP-75125 " " 125 " " " " " " 75 " " " B FWP-75150 " " 150 " " " " " " 100 " " " B FWP-75200 " " 200 " " " " " " 150 " " " B FWP-100100 100 " 100 " " " 50 ±0.2 25 50 " " 4 C FWP-100125 " " 125 " " " " " " 75 " " " C FWP-100150 " " 150 " " " " " " 100 " " " C FWP-100200 " " 200 " " " " " " 150 " " " C FWP-100250 " " 250 " " " " " " 200 " " " C FWP-125125 125 " 125 " " " 75 " " 75 " " " C FWP-125150 " " 150 " " " 50 " 37.5 100 " 25 " C FWP-125200 " " 200 " " " " " " 150 " " " C FWP-125250 " " 250 " " " " " " 200 " " " C FWP-150150 150 " 150 " " " 100 " 25 100 " 25 " C FWP-150200 " " 200 " " " " " " 150 " " " C FWP-150250 " " 250 " " " " " " 200 " " " C
自潤襯套LFB 內徑：Ø3～Ø160
自潤襯套LFB DRYMET LF內徑：Ø3～Ø28 請選擇適合的內徑、長度之Parts No.（例如）內徑15mm、長度8mm時，請以LFB-1508標示。 ※接合處雖不影響軸承的旋轉，但壓入時請避免其承受最大負荷之位置。 軸徑 軸承座 內徑 外徑 襯套厚度 長度 L 公差 0 -0.3 尺寸 公差 尺寸 H7 公差 Ød ØD 公差 T 公差 3 4 5 6 7 8 3 -0.025 -0.034 5 +0.012 0 3 5 +0.047 +0.017 1.0 0 -0.025 0303 0304 0305 0306 4 -0.025 -0.037 6 " 4 6 " " " 0403 0404 0405 0406 0408 5 " 7 +0.015 0 5 7 +0.055 +0.025 " " 0503 0504 0505 0506 0508 6 " 8 " 6 8 " " " 0603 0604 0605 0606 0607 0608 7 -0.025 -0.040 9 " 7 9 " " " 0705 0706 0707 0708 8 " 10 " 8 10 " " " 0805 0806 0807 0808 9 " 11 +0.018 0 9 11 +0.060 +0.030 " " 0906 10 " 12 " 10 12 " " " 1006 1007 1008 12 -0.025 -0.043 14 " 12 14 " " " 1206 1208 13 " 15 " 13 15 " " " 1308 14 " 16 " 14 16 +0.066 +0.035 " " 1408 15 " 17 " 15 17 " " " 1508 16 " 18 " 16 18 +0.070 +0.035 " " 17 " 19 +0.021 0 17 19 " " " 18 " 20 " 18 20 +0.075 +0.040 " " 19 -0.025 -0.046 22 " 19 22 " 1.5 0 -0.030 20 " 23 " 20 23 +0.080 +0.045 " " 22 " 25 " 22 25 " " " 24 " 27 " 24 27 " " " 25 " 28 " 25 28 +0.085 +0.050 " " 26 " 30 " 26 30 " 2.0 " 28 " 32 +0.025 0 28 32 +0.090 +0.050 " " ※壓入後內徑公差為參考值。 長度 L 公差 0 -0.3 壓入後 內徑公差 內徑 10 12 14 15 16 20 25 30 35 Ød +0.062 0 3 " 4 +0.065 0 5 0610 0612 " 6 0710 0712 " 7 0810 0812 0815 " 8 0910 +0.068 0 9 1010 1012 1015 1020 " 10 1210 1212 1215 1220 " 12 1310 1312 1315 1320 " 13 1410 1412 1414 1415 1416 1420 " 14 1510 1512 1515 1520 1525 " 15 1610 1612 1615 1620 1625 " 16 1710 1715 +0.071 0 17 1810 1812 1815 1820 1825 1830 " 18 1910 1915 1920 +0.081 0 19 2010 2012 2015 2020 2025 2030 " 20 2210 2212 2215 2220 2225 2230 " 22 2415 2420 2425 2430 " 24 2510 2512 2515 2520 2525 2530 2535 " 25 2615 2620 2625 2630 " 26 2812 2815 2820 2825 2830 +0.085 0 28 自潤襯套LFB DRYMET LF內徑：Ø30～Ø160 請選擇適合的內徑、長度之Parts No.（例如）內徑70mm、長度35mm時，請以LFB-7035標示。 ※接合處雖不影響軸承的旋轉，但壓入時請避免其承受最大負荷之位置。 軸徑 軸承座 內徑 外徑 襯套厚度 長度L 公差 0 -0.3 尺寸 公差 尺寸 H7 公差 Ød ØD 公差 T 公差 12 15 20 25 30 35 30 -0.025 -0.046 34 +0.025 0 30 34 +0.090 +0.050 2.0 0 -0.030 3012 3015 3020 3025 3030 3035 31 -0.025 -0.050 35 " 31 35 " " " 3115 3125 3130 32 " 36 " 32 36 " " " 3215 3220 3225 3230 35 " 39 " 35 39 +0.095 +0.055 " " 3512 3520 3525 3530 3535 38 " 42 " 38 42 " " " 3820 3825 3830 3835 40 " 44 " 40 44 " " " 4012 4015 4020 4025 4030 4035 45 " 50 " 45 50 +0.100 +0.060 2.5 0 -0.040 4520 4525 4530 4535 50 " 55 +0.030 0 50 55 +0.105 +0.060 " " 5020 5025 5030 5035 55 -0.025 -0.055 60 " 55 60 +0.110 +0.065 " " 5525 5530 5535 60 " 65 " 60 65 +0.120 +0.070 " " 6030 6035 65 +0.035 +0.005 70 " 65 70 +0.125 +0.075 " -0.030 -0.080 6530 70 " 75 " 70 75 " " " 7030 7035 75 " 80 " 75 80 +0.130 +0.075 " " 7530 7535 80 " 85 +0.035 0 80 85 " " " 85 +0.035 0 90 " 85 90 " " " 90 " 95 " 90 95 " " " 100 " 105 " 100 105 +0.140 +0.080 " " 110 " 115 " 110 115 " " " 120 " 125 +0.040 0 120 125 +0.145 +0.090 " " 130 +0.035 -0.005 135 " 130 135 " " " 140 " 145 " 140 145 +0.165 +0.100 " " 150 " 155 " 150 155 +0.185 +0.120 " " 160 " 165 " 160 165 " " " ※壓入後內徑公差為參考值。 長度 L 公差 0 -0.3 壓入後 內徑公差 內徑 40 50 60 70 80 90 95 100 Ød 3040 3050 +0.085 0 30 3140 " 31 3240 " 32 3540 3550 " 35 3840 " 38 4040 4050 " 40 4540 4550 +0.105 0 45 5040 5050 5060 +0.110 0 50 5540 5550 5560 " 55 6040 6050 6060 6080 " 60 6540 6550 6560 +0.190 +0.060 65 7040 7050 7060 7070 7080 " 70 7540 7550 7560 7580 " 75 8040 8050 8060 8080 +0.195 +0.060 80 8540 8550 8560 8580 " 85 9040 9050 9060 9090 " 90 10050 10070 10080 10095 100100 " 100 11050 11070 11095 110100 " 110 12050 12070 12095 120100 +0.200 +0.060 120 13050 13080 130100 " 130 14050 14080 140100 " 140 15050 15080 150100 " 150 16050 16080 160100 " 160
自潤凸襯襯套LFF.
自潤凸襯襯套LFF DRYMET LF 請選擇適合的內徑、長度之Parts No.（例如）內徑20mm、長度10mm時，請以LFF-2010標示。 軸徑 軸承座 內徑 外徑 凸緣 襯套厚度 長度 L 公差 0 -0.3 尺寸 公差 尺寸 H7 公差 Ød ØD ØF 公差 T2 公差 T1 公差 3 4 5 6 3 -0.025 -0.034 4.6 +0.012 +0 3 4.6 7 0 -0.8 0.8 0 -0.15 0.8 0 -0.025 0303 0305 4 -0.025 -0.037 5.6 " 4 5.6 9 " " " " " 0404 0406 5 " 7 +0.015 +0 5 7 10 " 1.0 " 1.0 " 0504 0505 0506 6 " 8 " 6 8 12 " " " " " 0605 0606 7 -0.025 -0.040 9 " 7 9 13 " " " " " 0705 8 " 10 " 8 10 15 " " " " " 0806 9 " 11 +0.018 +0 9 11 16 " " " " " 10 " 12 " 10 12 18 " " " " " 1006 12 -0.025 -0.043 14 " 12 14 20 " " " " " 1206 13 " 15 " 13 15 21 " " " " " 14 " 16 " 14 16 22 " " " " " 15 " 17 " 15 17 23 " " " " " 16 " 18 " 16 18 24 " " " " " 18 " 20 +0.021 +0 18 20 26 " " " " " 20 -0.025 -0.046 23 " 20 23 31 " 1.5 " 1.5 0 -0.030 22 " 25 " 22 25 33 " " " " " 24 " 27 " 24 27 35 " " " " " 25 " 28 " 25 28 36 " " " " " 26 " 30 " 26 30 38 " 2.0 " 2.0 " 28 " 32 +0.025 +0 28 32 40 " " " " " 30 " 34 " 30 34 42 " " " " " 31 -0.025 -0.050 35 " 31 35 45 " " " " " 32 " 36 " 32 36 46 " " " " " 35 " 39 " 35 39 49 " " " " " 38 " 42 " 38 42 52 " " " " " 40 " 44 " 40 44 54 " " " " " 45 " 50 " 45 50 60 " 2.5 " 2.5 0 -0.040 50 " 55 +0.030 +0 50 55 65 " " " " " 55 -0.025 -0.055 60 " 55 60 70 " " " " " 60 " 65 " 60 65 75 " " " " " ※壓入後內徑公差為參考值。 長度 L 公差 0 -0.3 壓入後 內徑公差 內徑 7 8 10 12 15 20 25 30 40 Ød +0.085 0 3 " 4 " 5 0607 0608 " 6 0707 " 7 0808 0810 0812 " 8 0910 +0.105 0 9 1007 1008 1010 1012 1015 +0.110 0 10 1207 1208 1210 1212 1215 " 12 1310 1315 " 13 1410 1412 1415 +0.190 +0.060 14 1510 1512 1515 1520 " 15 1610 1615 1620 " 16 1810 1812 1815 1820 +0.195 +0.060 18 2010 2012 2015 2020 2025 " 20 2210 2212 2215 2220 " 22 2415 2420 2425 " 24 2510 2512 2515 2520 2525 " 25 2615 2620 +0.200 +0.060 26 2812 2815 2820 " 28 3012 3015 3020 3025 3030 " 30 3125 " 31 3220 3225 3230 " 32 3512 3520 3525 3530 3540 " 35 3820 " 38 4012 4020 4025 4030 4040 " 40 4520 4525 4530 4540 " 45 5020 5030 5040 " 50 5530 5540 " 55 6030 3040 " 60
自潤平板LFP .
自潤平板LFP DRYMET LF 請選擇適合的厚度、寬度之Parts No. （例如）厚度1.5mm、寬度90mm時，請以LFP-1590標示。 Parts No. 厚度 寬度 長度 Ｔ 公差 W L LFP-1080 1.0 -0.03 -0.13 80 500 LFP-1590 1.5 " 90 " LFP-20100 2.0 " 100 " LFP-25100 2.5 " " " 墊圈、平板之安裝方法 4接著劑安裝方法 採用埋入安裝時，可以不用定位銷，而改用接著劑。 著劑最好選用合成樹脂接著劑。 請注意只有用接著劑安裝時，才會有脫落的情形發生。
自潤墊圈LFW .
自潤墊圈LFW DRYMET LF 請選擇適合的內徑、厚度之Parts No.（例如）內徑20mm、厚度1.5mm時，請以LFW-2015標示。 Parts No. 內徑 外徑 厚度 定位銷 定位銷位置 Ød 公差 ØD 公差 T 公差 H 公差 P.C.D 公差 LFW-0815 8 +0.25 0 16 0 -0.25 1.5 -0.03 -0.08 1 +0.30 +0.10 12 ±0.12 LFW-1015 10 " 18 " " " " " 14 " LFW-1215 12 " 24 " " " 1.5 +0.375 +0.125 18 " LFW-1415 14 " 26 " " " 2 " 20 " LFW-1615 16 " 30 " " " " " 23 " LFW-1815 18 " 32 " " " " " 25 " LFW-2015 20 " 36 " " " 3 " 28 " LFW-2215 22 " 38 " " " " " 30 " LFW-2415 24 " 42 " " " " " 33 " LFW-2615 26 " 44 " " " " " 35 " LFW-2815 28 " 48 " " " 4 " 38 " LFW-3215 32 " 54 " " " " " 43 " LFW-3815 38 " 62 " " " " " 50 " LFW-4215 42 " 66 " " " " " 54 " LFW-4820 48 " 74 " 2.0 " " " 61 " LFW-5220 52 " 78 " " " " " 65 "
自潤襯套SFP#500SP
自潤平面滑板 SFP #500SP 請選擇適合的寬度、長度之Parts No. （例如）寬度28mm、長度150mm時，請以SFP-28150標示。 Parts No. 寬度 長度 厚度 裝配孔之孔距 安裝螺栓 W L T 公差 a b 種類 種類 SFP-1875 18 75 10 +0.04 +0.01 15 45 M6內六角型 2 SFP-18100 " 100 " " 25 50 " " SFP-18125 " 125 " " " 75 " " SFP-18150 " 150 " " " 100 " " SFP-2875 28 75 " " 15 45 " " SFP-28100 " 100 " " 25 50 " " SFP-28125 " 125 " " " 75 " " SFP-28150 " 150 " " " 100 " " SFP-3875 38 75 " " 15 45 " " SFP-38100 " 100 " " 25 50 " " SFP-38125 " 125 " " " 75 " " SFP-38150 " 150 " " " 100 " " SFP-4875 48 75 " " 15 45 " " SFP-48100 " 100 " " 25 50 " " SFP-48125 " 125 " " " 75 " " SFP-48150 " 150 " " " 100 " " Parts No. 寬度 長度 厚度 裝配孔之孔距 安裝螺栓 W L T 公差 a b c d e 種類 個數 SFP-35100 35 100 10 ±0.025 20 60 － － － M8 扁平頭小螺栓 2 SFP-35150 " 150 " " " 55 55 － － " 3 SFP-35200 " 200 " " " 55 50 55 － " 4 SFP-35250 " 250 " " " 70 70 70 － " 4 SFP-35300 " 300 " " " 65 65 65 65 " 5 SFP-35350 " 350 " " " 80 75 75 80 " 5 SFP-50100 50 100 " " " 60 － － － " 2 SFP-50150 " 150 " " " 55 55 － － " 3 SFP-50200 " 200 " " " 55 50 55 － " 4 SFP-50250 " 250 " " " 70 70 70 － " 4 SFP-50300 " 300 " " " 65 65 65 65 " 5 SFP-50400 " 400 " " " 90 90 90 90 " 5 Parts No. 寬度 長度 厚度 裝配孔之孔距 安裝螺栓 W L T 公差 a b c d e 種類 個數 SFP-75150 75 150 10 ±0.025 20 110 － － － M8 扁平頭小螺栓 4 SFP-75200 " 200 " " " 80 80 － － " 6 SFP-75250 " 250 " " " 105 105 － － " 6 SFP-75300 " 300 " " " 85 90 85 － " 8 SFP-75400 " 400 " " " 120 120 120 － " 8 SFP-75500 " 500 " " " 115 112 115 115 " 10
